1WARNINGA radio-controlled model is not a toy and is not intended for persons under 16 years old. Keepthis kit out of the reach of younger children,
10 Collect the following items(1) Stab(1) Fuselage (with bottom wing installed)(1) FinTail Construction.AABB1. Install stab in opening at rear
116. Install the fin in the slot and check the align-ment. It can be adjusted a small amount by sandingthe fin post area where it goes into the fu
122. Slide gear leg into slot on side of fuselage andinstall retaining bolts through access holes on the sideand middle of fuselage. Be sure to us
135. The wheel pants have the 1/2” hole predrilled ineach pant. The 1/8” hole for the mounting bolt must bedrilled.6. Block the tail of the pl
14Tail wheel Mounting1. Collect the following parts:(1) tail wheel bracket(1) tail wheel(2) 1/8” wheel collars(2) tail wheel springs(2) #6 x 1/2”
156. Twist the end of the spring on to the hornbracket. Insert the long wire end around thesecond horn bracket. Twist the wire so that itwill stay h
16Top Wing Mounting1. Locate the following items.(4) cabane struts(2) I-Struts(1) Top Wing(1) Bottom Wing(1) Fuselage(2) 1/4-20 x 2” wing bolts(20
174. Screw the eyebolts into the holes in the wing,they are set at a slight angle since the strut does notgo perpendicular to the wings. The botto
18FLYING WIRES1. Locate the following parts Roll of braided cable (8) metal plates (4) 2-56 rigging couplers (4) golden clevis (4) metal clev
196. Loop the end of the cable back though thebrass tube. Use pliers and crimp the brass tubing onto thecable to secure it.5. Insert the cable
21. Fuselage2. Cowl3. Fin4. Rudder5. I-Strut (2)6. Landing gear legs (2)7. Wheel Pants (2)8. Canopy9. Belly pan10. Stab11. Elevators (left and
20Belly pan1. Mount the bottom wing in place.2. Place belly pan in place and mark the outlineon the bottom of wing. 3. Remove belly pan an
21Engine Mounting1. Collect the following items.(2) motor mounts(4) 8-32x1” bolts(4) 8-32x1-1/4” bolts(4) 8-32 t-nuts(4) 8-32 aircraft lock nuts(1
227. Take the other motor mount and clamp to theother side of the engine. Set the motor mounts on aflat surface and make sure both sit flat on the
23Fuel Tank1. Collect the following item(1) fuel tank 500cc (16.91 oz.)(1) rubber tank stopper(1) clunk (1) 3mm x 25mm screw(1) cap washer large(1
246. If you use a Y-S engine that pressurizes thetank, you should wrap the tank with nylon strappingtape to make sure the pressure does not split
25Cowl Mounting1. Collect the following items.(1) Cowl(4) 4-40 x 1” Socket Head Bolt(4) #4 Washer(4) 1/4” pieces silicone tubing(1) 4” x 12” Clear
261. Install the servos in the tray with the elevatorservo all the way against the right side of the plane.For maximum throw you will need longer
273. Insert the 1/8” tubing into the rear cable exithole. Push the tubing while guiding it through thefuselage.4. Thread the 2-56 end of the cab
28Elevator Pushrod1. Collect the following items(1) 8mm x 17” wooden dowel(2) 1/2” shrink tubing(2) 2-56 x 7-1/2” pushrods threaded one end(1) 2-5
297. Install a clevis on the 6” pushrod and attachto elevator arm on servo. Make a mark on the rodand the dowel where they cross 1” from the end o
3Motor Mounts (2) pcs(4) 8-32 x 1” Socket head bolts(4) 8-32 x 1-1/4” Socket head bolts(4) 8-32 T-nuts(4) aircraft lock nuts(12) #8 flat washersFlying
30CG BalancingBalancing the Pitts is very important, you might need to use weight dependingon the servos and engine that you use. Start out with the b
4Before you begin assembling your Pitts ARF, take sometime to read through this entire instruction book. It isdesigned to take you step-by-step throu
5ITEMS NEEDED TO COMPLETE THIS AIRCRAFT 1 RADIO GUIDANCE SYSTEM (4 CHANNELMINIMUM REQUIRED WITH 7 SERVOS) You will need 7 servos for the plane. we
6WING ASSEMBLY1. Collect the following parts:(1) Left wing(1) Right wing(1) Left aileron(1) Right aileron(12) CA hingesAILERON INSTALLATION2. Loca
7AILERON SERVO INSTALLATIONNote: The following pictures may not exactly matchthe hardware you are using. Always check theradio manufacturer's in
86. Thread on to one end of a 2-56 x 1-3/4” pushrod a nut and Golden Clevis. Mount the pushrod onto the the horn brack-et. Thread the other 2-56
9Before mounting the tail the bottomwing should be installed. Collect the following items(1) Fuselage(1) Bottom wing(2) Wing dowels (8mm x 40mm)(2)
Comments to this Manuals