CCAARRLL GGOOLLDDBBEERRGG PPRROODDUUCCTTSS LLTTDD..CCAARRP.O. Box 818, Oakwood, GA 30566 • 678-450-0085 • Fax: 770-532-2163 • www.carlgoldbergprod
10Wild Stick 12011. Epoxy the fin in place making sureit is square to the stab and centeredon the fuselage in the rear.Flying WiresLocate the followin
11Wild Stick 1203.Mount the aluminum bracket on thebottom of the fuselage using the two2mmx10mm screws. Use the tail wheel bracket to alignthe flying
12Wild Stick 1204.Take one of the 7” pushrods andmake sure the clevis is screwed onwith about 1/16” of threads showingon the inside. Install the clevi
13Wild Stick 1201. Fit the landing gear to the bottomof the fuselage and install the fourscrews and flat washers. Use locktiton the screws.2. install
14Wild Stick 120Tail wheelLocate the following Parts:Tail wheel brackettail wheelrudder tiller armwire axel3mm wheel collarnylon control horn brackets
15Wild Stick 120Engine Installationlocate the following parts:1. Two motor mounts2. Four 4mmx20mm screws3. Four 4mm blind nuts4. Four 4mmx25mm bolts5.
16Wild Stick 1203. Center the engine on the firewalland mark the location of the fourmounting bolts. 4. install the four blind nuts in thefirewall. Th
17Wild Stick 1202. install the servos using the hard-ware supplied with the radio. Use thestings installed in the wing to pullthe wires through to the
18Wild Stick 1205. Locate one of the 3mm pushrods,metal clevis, two 3mm nuts and sili-cone clevis keeper. Make sure theclevis is screwed on the pushro
19Wild Stick 1209. Locate the pull-pull cable, cableends and cable swages. Take two ofthe rigging couplers and two of theswages and insert the cable t
2Wild Stick 120WARNING! THIS IS NOT A TOY!THIS IS NOT A BEGINNERS AIRPLANEThis R/C kit and the model you will build from it is not a toy! It is capab
20Wild Stick 1202. On Four stroke engines you need tobend a z-bend in the pushrod andattach to the throttle arm.Throttle servo1. Use a long drill for
21Wild Stick 1205. Slide the 5mm plastic tube on thethrottle pushrod until it extends1/4” through the firewall. Installthe pushrod connector on the s
22Wild Stick 120Fuel Tank1. Locate the fuel tank and hard-ware. 2. Assemble the tank cap with the bigwasher, the rubber stopper, and thelittle washer
23Wild Stick 1204.Install stopper in tank and tightenthe bolt in the center until stopper issnug. Don’t over tighten. Clunkshould move freely and vent
24Wild Stick 120(2). Crow. In this mode the two out-board ailerons move to the up posi-tion and the flaps move to the downposition. This is a very hig
3Wild Stick 120Wild StickWild StickCongratulations on your purchase of the Lanier Wild Stick 120. This is a veryunique aircraft, with great 3-D capab
4Wild Stick 120Parts LayoutFuselage 1wing panels 2ailerons 2Flaps 2Stabilizer 1Elevators 2Fin 1Rudder 1landing Gear 1ColorsRed True red #
5Wild Stick 120Landing Gear 14mmx12mm bolts 44mm washers 64mm wheel collars 44mm axels 24mm lock nuts 23.5” wheels 2Motor Mounts 24mmx20mm bolts 44mm
6Wild Stick 120BUILDINGINSTRUCTIONSBefore starting to build this kit, weurge you to read through theseinstructions. They contain someimportant buildi
7Wild Stick 1203. Spread epoxy on the root rib ofeach wing panel. Use a thin scrap ofwood and work some of the epoxydown into the slots for the dihedr
8Wild Stick 120Align holes overhinge line2. Remove the elevators from thestab and make sure all the hinges arecentered in the slots. To make surethe h
9Wild Stick 1207. use a razor blade or e-xacto knifeto carefully remove the coveringinside the marks on the bottom of thestab. Cut carefully so as not
Comments to this Manuals